Hoisting and Driving Tools
140-Pound (63.5 kg) Safety Style Hammer Assembly with Cast Anvil
& AWJ Pin Down
140-Pound (63.5 kg) In-Hole Hammer Assembly with Swivel
& AW Box Down
|
Safety Type & In-Hole Style “SPT” Drive Hammers, Parts & Accessories – are available from USExploration Equipment Company – typically attached to the “business end” of a Cathead Rope or a Safe-T-Driver Hoist (free-spooling) cable, these tools are designed to help the operator complete ASTM Procedure D1586-08a along with the appropriate down-hole sampling device – this test includes lifting and (freely) dropping a 140-Pound (63.5 kg) weight exactly 30-inches (762mm) on top of 1-3/4-inch (44.5 mm) Outside diameter (AW or AWJ) Drill Rods to achieve the correct “N” value as it relates to determining material density and proper foundation design. The 300-Pound (136 kg) version is typically used to drive Flush Joint Casing through formations that are too difficult to advance Solid Stem or Hollow Stem Augers.
The In-Hole Style Hammer works best in conjunction with a Safe-T-Driver Hoist as the 2-7/8” (73mm) OD assembly can be lowered into Flush Joint Casing or Hollow Stem Augers, to advance a Sampler, break up material that has worked its way inside the annular space or simply act as an internal cutting face in addition to the Casing Shoe or Cutterhead.
When ordering, make sure you specify Safety Style or In-Hole Hammer assembly…
Back to Top PDF |
140-Pound (63.5 kg)
Safety Style Hammer Assembly
Pin Down Connection |
Assembly
Weight |
Assembly
Part Number |
AW |
190-Pounds
(86.2 kg) |
26001 |
AWJ |
190-Pounds
(86.2 kg) |
26002 |
Outer Sleeve |
127-Pounds
(57.6 kg) |
26022 |
Hammer
Center Rod - AW |
28-Pounds
(12.7 kg) |
26025 |
Hammer
Center Rod – AWJ |
28-Pounds
(12.7 kg) |
26026 |
Threaded Cap |
14-Pounds
(6.4 kg) |
26029 |
300-Pound (136 kg)
Safety Style Hammer Assembly
Pin Down Connection |
Assembly
Weight |
Assembly
Part Number |
NW |
351-Pounds
(159.2 kg) |
26022 |
NWJ |
351-Pounds
(159.2 kg) |
26003 |
Outer Sleeve |
295-Pounds
(133.8 kg) |
26024 |
Hammer
Center Rod - NW |
39-Pounds
(17.7 kg) |
26027 |
Hammer
Center Rod - NWJ |
39-Pounds
(17.7 kg) |
26028 |
Threaded Cap |
17-Pounds
(7.7 kg) |
26030 |
140-Pound (63.5 kg)
In-Hole Style Hammer Assembly
Box Down Connection |
Assembly
Weight |
Assembly
Part Number |
AW |
180-Pounds
(63.5 kg) |
26215 |
Swivel Assembly |
5-Pounds
(2.3 kg) |
26216 |
Bolt & Nut Set
Fits
Swivel Assembly |
1-Pound
(.45 kg) |
26217 |
Impact Block |
168-Pounds
(76.2 kg) |
26218 |
AWJ Full-Swivel Hoisting Plug (top) & AW/ AWJ Rod “Slip” Ring (bottom)
|
Hoisting & Rod Handling Tools for J-Series, W-Design & API style Drill Rods – are available from USExploration Equipment Company. Full-Swivel style Hoisting Plugs and Rod (Slip) Rings are all DCDMA compatible. When ordering, simply choose the appropriate thread style and corresponding tool for your application…
Back to Top PDF |
Hoisting Plug, Full-Swivel Style
with
Heavy Duty Bail |
Special Feature |
Assembly Part Number |
A Rod Pin Down |
|
25014 |
N-4 Pin Down |
|
25015 |
AW Pin Down |
W-Design Drill Rods |
25004 |
AWJ Pin Down |
J-Series Drill Rods |
25005 |
NW Pin Down |
W-Design Drill Rods |
25006 |
NWJ Pin Down |
J-Series Drill Rods |
25007 |
2-3/8” API IF Pin Down |
Drill Pipe |
25043 |
2-3/8” Mayhew Regular Pin Down |
Drill Pipe |
25040 |
2-3/8” API Regular Pin Down |
Drill Pipe |
25046 |
2-7/8” API IF Pin Down |
Drill Pipe |
25037 |
2-7/8” API Regular Pin Down |
Drill Pipe |
25047 |
3-1/2” API IF Pin Down |
Drill Pipe |
25049 |
3-1/2” API Regular Pin Down |
Drill Pipe |
25048 |
HQ Wireline Pin Down |
Thinwall Wireline Drill Rods |
25044 |
NQ Wireline Pin |
Thinwall Wireline Drill Rods |
25045 |
3” Double-Start Sonic Rod Pin Down |
Sonic Drill Rods |
300-500-113 |
5-1/2” Double-Start Sonic Casing Pin Down |
Sonic Casing |
300-500-117 |
7” Double-Start Sonic Casing Pin Down |
Sonic Casing |
300-500-123 |
CR-50 Pin Down |
Atlas Copco – Craelius
Drill Rods |
25041 |
Rod (Slip) Ring with Heavy Duty Bail |
Special Feature |
Assembly Part Number |
A Drill Rods |
Closed |
25010 |
AW & AWJ Drill Rods |
Closed |
25008 |
AW & AWJ Drill Rods |
Open |
25050 |
N Drill Rods |
Closed |
25013 |
NW & NWJ Drill Rods |
Closed |
25011 |
|
SPT Automatic Hammer Assemblies - are available from USExploration Equipment Company - they give you extremely consistent and accurate Standard Penetration Test (SPT) results, meeting all ASTM-D-1586-99 requirements in every state. These assemblies can be adapted to virtually any 5-foot stroke machine because the hammer simply swings in from a “stored” position to the “on-hole” position. Since raising and lowering is done hydraulically, set up is quick and almost effortless. For maximum safety, all moving parts are enclosed, including the impact area between the weight and the anvil. Each assembly includes a Hammer Case, Slug, Hydraulic Cylinder, Hydraulic Motor, Guide and Sub. When ordering, specify the make and model for the rig installation and hydraulic circuitry you intend to utilize… Back to Top PDF |
Drill Rig
Make & Model |
Assembly
Part Number |
USExploration Equipment Company
Model S-27CS |
25052 |
USExploration Equipment Company
Model S-27CRS |
25051 |
USExploration Equipment Company
Model S-27CS-T |
25052 |
USExploration Equipment Company
Model S-27CRS-T |
25051 |
Mobile Drill
Model B-53 |
25053 |
Mobile Drill
Model B-57 |
25054 |
Mobile Drill
Model B-58 |
25054 |
Mobile Drill
Model B-59 |
25055 |
Mobile Drill
Model B-61HD |
25056 |
Mobile Drill
Model B-61HDX |
25056 |
|
Safe-T-Driver ® Hoist with ¼-inch (6.4mm) Cable
|
Safe-T-Driver ® Hoists - are available from USExploration Equipment Company as an alternative to a cathead for SPT sampling operations. The simple design allows the operator to raise and lower a safety hammer assembly 30-inches (762mm) - attached directly to the ¼-inch (6.4mm) cable that is spooled on the drum itself. The handle at the panel allows the operator to control the lift (visually), then pull the same lever down, pushing enough oil through the system to an over-running clutch attached to the hoist drum, creating a free-fall “action” for the 140-pound (63.5 kg) weight as part of the requirements for ASTM-D-1586-99 in every state. This same hoist can be used to “bump-out” when required, unlike other automatic or semi-automatic driving devices. The field kit includes a hand brake when conditions require it – simply specify the rig make and model when ordering…
Back to Top PDF |
Safe-T-Driver ®
Hoist
Capacity |
Maximum
Hoisting Speed
Up |
Maximum Cable Spooling
Capacity |
Minimum
Hydraulic Operating Requirements |
Assembly
Part Number
|
1,140-pound
(517.1 kg) |
1,132 rpm |
350-feet
(107m) |
25 gpm
@ 2,500 psi |
7100-21012-25 |
Safe-T-Driver ®
Assembly
Components |
Assembly
Part Number
|
Hoist Drum
&
Mounting Parts |
7100-71026-08 |
Cable & Clevis
for
Mechanical Brake
35-feet (10.7m) |
7100-050366-35 |
Cable & Clevis
for
Mechanical Brake
44-feet (13.4m) |
7100-050366-44 |
Over-Running
Clutch
Assembly |
7100-140592-01 |
Hydraulic Motor
Assembly |
7100-71012-31 |
Hoist
Shaft Assembly |
7100-213055 |
Mechanical Brake
Handle Assembly |
7100-216724 |
|
